BMW K 1100 LT Page 189 Repair Manual Download

Page: 189 / 364

23.15

Disassembling and assembling input
shaft

Disassembling input shaft

•

Clamp spline end of input shaft in vice with jaw
guard.

•

Remove retaining ring (1).

•

Using universal puller,

BMW No. 00 7 500

, and

pressure tool (arrow), remove spur gear (3) to-
gether with taper roller bearing (2).

•

Also remove second taper roller bearing.

Assembling input shaft

•

Fit washer (6), coil spring (5), thrust piece (4) and
spur gear (3) on input shaft.

•

Using universal puller, tension spur gear against
coil spring until the 2nd groove (arrow) can be
seen ahead of the spur gear.

•

Heat taper roller bearing to 100 °C and fit in po-
sition.

•

Fit retaining ring (1) in front of the taper roller
bearing.

LT230170

00 7 500

LT230180

00 7 500

LT230190

Downloaded from

www.Manualslib.com

manuals search engine

Summary of Contents for K 1100 LT













































































































































































































































































































































































Search results

Summary of Contents for K 1100 LT

Reviews:

Related manuals for K 1100 LT

Brands by name

Popular brands

BMW K 1100 LT, Repair Manual

Search results

Summary of Contents for K 1100 LT

Reviews:

Related manuals for K 1100 LT

Brands by name

Popular brands