manualshive.com logo in svg

BMW K 1100 LT, Repair Manual, Page: 207 / 364

Share
Download
BMW K 1100 LT Repair Manual Download Page 207

31.5

Removing telescopic fork

•

Secure lifting gear, 

BMW No. 00 1 510

, to oil 

sump.

•

Remove fuel tank.

•

Remove front mudguard.

•

Remove brake caliper.

Removing fork stabilisor

•

Release brake distributor (1).

•

Disconnect ABS plug connection of sensor line 
(2) under fuel tank.

•

Remove fork stabiliser.

•

Remove front wheel.

•

Remove handlebar with fittings.

Removing telescopic fork without fork 
bridge

•

Release clamping screws (1,2), pull down 
telescopic fork and remove.

Removing telescopic fork with fork 
bridge

Removing upper fork bridge

•

Release hexagon nut (4).

•

Release locking tube (5).

•

Disconnect plug connection for ignition lock (3).

•

Loosen clamping screws (1).

•

Remove fork bridge.

•

Remove setting ring (6).

•

Remove fork by pulling from below together with 
light hammer blows (plastic-headed hammer) on 
the steering tube.

LT310010

2

1

3

4

5

1

1

6

2

LT310020

2

1

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for K 1100 LT













































































































































































































































































































































































Reviews:

No comments