BMW K 1100 LT Repair Manual Download Page 147

Page: 147 / 364

17.5

Changing coolant

Draining coolant

•

Remove fuel tank.

•

Release cap (1) on filler neck.

•

[RS]

Remove lower section of fairing

•

Release screw plug (2) on water pump

[RS]

, or

water temperature sensor

[LT]

•

Note gasket.

Tightening torque:

Drain plug, temperature sensor

...................... 9 Nm

Filling with coolant

•

Fill with coolant up to lower edge of filler neck (1).

Coolant:

Concentration (down to – 28 °C)
Antifreeze

......................................................40 %

Water

..............................................................60 %

Capacity

.....................................3.0 l (0.66 Imp.gal)

Quantity in expansion tank

.......0.4 l (0.088 Imp.gal)

•

Crank engine with starter while kneading hose
between water pump and filler neck

•

Assemble motorcycle.

LT170010

LT170020

Downloaded from

www.Manualslib.com

manuals search engine

Summary of Contents for K 1100 LT













































































































































































































































































































































































Search results

Summary of Contents for K 1100 LT

Reviews:

BMW K 1100 LT, Repair Manual, Page: 147 / 364

Search results

Summary of Contents for K 1100 LT

Reviews: