BMW K 1100 LT Page 98 Repair Manual Download

Page: 98 / 364

12.12

•

Remove regulator (8) with carbon brushes.

•

Carefully lift out armature (9) together with bear-
ing (10).

•

Remove bearing (10) from armature shaft.

•

Unsolder stator (11) on diode plate (12); mark the
wires.

•

Remove diode plate.

•

Remove O-ring (14).

•

Install in the reverse order of removal.

Note:

During assembly, insulate the solder points on the
diode plate with silicone. Coat bearing seat in hous-
ing with Molykote paste.

Checking exciter winding

•

Using the test probes of the BMW diagnosis test-
er,

BMW No. 61 1 510

, measure the resistance

across the slip rings.

Nominal resistance.......................................7 ± 1

Ω

LT120100

61 1 510

LT120110

Downloaded from

www.Manualslib.com

manuals search engine

Summary of Contents for K 1100 LT













































































































































































































































































































































































Search results

Summary of Contents for K 1100 LT

Reviews:

Related manuals for K 1100 LT

Brands by name

Popular brands

BMW K 1100 LT, Repair Manual

Search results

Summary of Contents for K 1100 LT

Reviews:

Related manuals for K 1100 LT

Brands by name

Popular brands