BMW K 1100 LT Page 179 Repair Manual Download

Page: 179 / 364

23.5

Removing transmission (gearbox)

Preparatory work

•

[RS]

Remove left fairing side section

•

Remove exhaust system.

•

Disconnect CAT plug connection for oxygen
sensor.

•

Remove left and right footrest plate.

•

Remove rear mudguard.

•

Remove rear brake caliper.

•

Remove rear wheel.

•

Remove suspension strut.

•

Remove rear wheel drive.

•

Remove swinging arm.

•

Remove rear cover panel with coolant level
equalising tank.

•

Remove Motronic control unit.

•

Remove battery.

•

[ABS I]

Remove control unit.

•

[ABS I]

Detach pressure modulators from holder

and secure to rear section of frame.

•

[ABS I]

Remove holder for pressure modulators.

•

[ABS II]

Remove ABS unit.

•

Remove battery carrier.

•

Remove starter motor.

Note:

Secure brake caliper, pressure modulators, reser-
voir and, footrest plate with adhesive tape to frame.

Note:

For removal of ABS unit see Group 34, “Removing
ABS unit”.

LT230430

Downloaded from

www.Manualslib.com

manuals search engine

Summary of Contents for K 1100 LT













































































































































































































































































































































































Search results

Summary of Contents for K 1100 LT

Reviews:

Related manuals for K 1100 LT

Brands by name

Popular brands

BMW K 1100 LT, Repair Manual

Search results

Summary of Contents for K 1100 LT

Reviews:

Related manuals for K 1100 LT

Brands by name

Popular brands