SMARTLINK
I&II
MDS921AE-10BTS - MDS
Configuration
To setup the router, move the cursor “
appears, type the supervisor password. The default supervisor password is
will be prompted as “
*
“ sym
----------------------------------------------------------------------
Command: enable <CR>
Message: Please input the following information.
Supervisor password:
****
----------------------------------------------------------------------
Note: The factory default Supervisor passwords is “root”.
In this sub menu, you can setup management features and upgrade software, backup the system
configuration and restore the sy
For any changes of configuration, you have to write the new configuration to EPROM and reboot
the router to work with new setting.
The screen will prompt as follow.
>> enable
Modify command privilege
setup
Configure system
status
Show running system status
show
View system configuration
write
Update flash configuration
reboot
Reset and boot system
Ping
Packet internet groper command
admin
Setup management features
utility
TFTP upgrade
Exit
Quit system
The description of the commands are:
Command
enable
Modify command privilege. When you login via serial console or Telnet, the
router defaults to a program execution (read
the configuration and write changes to nonvolatile RAM (NVRAM), you must
work in enable mode.
setup
To configure the product, you have to use the setup command.
status
View the status of product.
show
Show the system and configuration of product.
write
Update flash configuration. After you have completed all necessary setting,
make sure to write the new configuration to NVRAM by “
reboot the system, or all of your changes will not take effect.
reboot
Reset and boot system. After you
sure to write the new configuration to NVRAM and reboot the system by
“
reboot
” command, or all of your changes will not take effect.
ping
Packet internet groper command.
admin
You can setup management
utility
Upgrade software and backup and restore configuration are done via “
command.
exit
Quit system
S957AE-10BTS User Manual
Page 92 of 113
To setup the router, move the cursor “
>>
” to
enable
and press enter key. While the screen
appears, type the supervisor password. The default supervisor password is
“ symbol for system security.
----------------------------------------------------------------------
Message: Please input the following information.
----------------------------------------------------------------------
Note: The factory default Supervisor passwords is “root”.
In this sub menu, you can setup management features and upgrade software, backup the system
configuration and restore the system configuration via utility tools.
For any changes of configuration, you have to write the new configuration to EPROM and reboot
the router to work with new setting.
The screen will prompt as follow.
Modify command privilege
Configure system
Show running system status
View system configuration
Update flash configuration
Reset and boot system
Packet internet groper command
Setup management features
TFTP upgrade utility
Quit system
The description of the commands are:
Description
Modify command privilege. When you login via serial console or Telnet, the
router defaults to a program execution (read-only) privileges to you. To change
configuration and write changes to nonvolatile RAM (NVRAM), you must
work in enable mode.
To configure the product, you have to use the setup command.
View the status of product.
Show the system and configuration of product.
Update flash configuration. After you have completed all necessary setting,
make sure to write the new configuration to NVRAM by “
write
reboot the system, or all of your changes will not take effect.
Reset and boot system. After you have completed all necessary setting, make
sure to write the new configuration to NVRAM and reboot the system by
” command, or all of your changes will not take effect.
Packet internet groper command.
You can setup management features in this command.
Upgrade software and backup and restore configuration are done via “
command.
Quit system
and press enter key. While the screen
appears, type the supervisor password. The default supervisor password is
root
. The password
In this sub menu, you can setup management features and upgrade software, backup the system
For any changes of configuration, you have to write the new configuration to EPROM and reboot
Modify command privilege. When you login via serial console or Telnet, the
only) privileges to you. To change
configuration and write changes to nonvolatile RAM (NVRAM), you must
To configure the product, you have to use the setup command.
Update flash configuration. After you have completed all necessary setting,
write
” command and
reboot the system, or all of your changes will not take effect.
have completed all necessary setting, make
sure to write the new configuration to NVRAM and reboot the system by
” command, or all of your changes will not take effect.
Upgrade software and backup and restore configuration are done via “
utility
”
