SMARTLINK
I&II
MDS921AE-10BTS - MDS
WAN
The router supports 8 PVC, private virtual circuit, and so you can setup eight WAN, WAN1 to
WAN8. Move the cursor “
>>
----------------------------------------------------------------------
Command: setup wan <1~8>
Message: Please input the following information.
Interface number <1~8>:
1
----------------------------------------------------------------------
>> protocol
Link type protocol
address
IP address and subnet mask
vpi_vci
Configure VPI/VCI value
encap
Configure encapsulation type
qos
Configure VC QoS
isp
Configure account name, password and idle time
ip_type
Configure IP type in PPPoA
list
WAN interface configuration
There are four types of protocols, IPoA, EoA, PPPoA and PPPoE, which you can setup.
For dynamic IP of PPPoA and PPPoE, you do not need to setup IP address and subnet mask.
There is an unique VPI and VCI value for Internet connection supported by ISP. The range of VIP
is from 0 to 255 and VCI from 0 to 65535.
There are two types of encapsulation types, VC
You can setup virtual circuit quality of service, VC QoS, using qos command. The pr
UBR, CBR, VBR-rt and VBR
Move the cursor to qos and press enter.
>> class
Configure QoS class
pcr
Configure peak cell rate (kbps)
scr
Configure sustainable cell rate
mbs
Configure max. burst size (cell)
ISP command can configure account name, password and idle time. Idle time are from 0 minute to
300 minutes.
Most of the ISP use dynamic IP for PPP connection but some of the ISP use static IP. Configure
the IP type, dynamic or fixed, via ip_type command.
You can review the WAN interface configuration via list command.
S957AE-10BTS User Manual
Page 101 of 113
The router supports 8 PVC, private virtual circuit, and so you can setup eight WAN, WAN1 to
>>
“ to
wan
and press enter. To setup WAN1, type
1
----------------------------------------------------------------------
Command: setup wan <1~8>
Message: Please input the following information.
----------------------------------------------------------------------
Link type protocol
IP address and subnet mask
Configure VPI/VCI value
Configure encapsulation type
Configure VC QoS
Configure account name, password and idle time
Configure IP type in PPPoA and PPPoE
WAN interface configuration
There are four types of protocols, IPoA, EoA, PPPoA and PPPoE, which you can setup.
For dynamic IP of PPPoA and PPPoE, you do not need to setup IP address and subnet mask.
VCI value for Internet connection supported by ISP. The range of VIP
is from 0 to 255 and VCI from 0 to 65535.
There are two types of encapsulation types, VC-Mux and LLC.
You can setup virtual circuit quality of service, VC QoS, using qos command. The pr
rt and VBR-nrt. The peak cell rate can be configured from 64kbps to 2400kbps.
Move the cursor to qos and press enter.
Configure QoS class
Configure peak cell rate (kbps)
Configure sustainable cell rate (kbps)
Configure max. burst size (cell)
ISP command can configure account name, password and idle time. Idle time are from 0 minute to
Most of the ISP use dynamic IP for PPP connection but some of the ISP use static IP. Configure
the IP type, dynamic or fixed, via ip_type command.
You can review the WAN interface configuration via list command.
The router supports 8 PVC, private virtual circuit, and so you can setup eight WAN, WAN1 to
1
.
There are four types of protocols, IPoA, EoA, PPPoA and PPPoE, which you can setup.
For dynamic IP of PPPoA and PPPoE, you do not need to setup IP address and subnet mask.
VCI value for Internet connection supported by ISP. The range of VIP
You can setup virtual circuit quality of service, VC QoS, using qos command. The product supports
nrt. The peak cell rate can be configured from 64kbps to 2400kbps.
ISP command can configure account name, password and idle time. Idle time are from 0 minute to
Most of the ISP use dynamic IP for PPP connection but some of the ISP use static IP. Configure
