SMARTLINK
I&II
MDS921AE-10BTS - MDS
Bridge
You can setup the bridge parameters in bridge command. If the product is configured as a router,
you do not want to setup the bri
>> gateway
Default gateway
static
Static bridging table
You can setup default gateway IP via gateway command.
You can setup 20 sets of static bridge in static command. After entering
will prompt as below:
>> add
Add static MAC entry
delete
Delete static MAC entry
modify
Modify static MAC entry
list
Show static bridging table
After enter add menu, the screen will prompt as follow
>> mac
Configure MAC address
lan_port
Configure LAN interface bridging type
wan1_port
Configure WAN1 interface bridging type
wan2_port
Configure WAN2 interface bridging type
wan3_port
Configure WAN3 interface bridging type
wan4_port
Configure WAN4 interface bridging type
wan5_port
Configure WAN5 interface bridging type
wan6_port
Configure WAN6 interface bridging type
wan7_port
Configure WAN7 interface bridging type
wan8_port
Configure WAN8 interface bridging type
list
Show static bridging table
VLAN
Virtual LAN (VLAN) is defined as a group of devices on one or more LANs that are configured so
that they can communicate as if they were attached to the same wire,
on a number of different LAN segments. Because VLAN is based on logical instead of physical
connections, it is extremely flexible.
The specification of VLAN function is as follow:
•
The unit supports up to 8 active VLANs with s
4096 possible VLANs specified in IEEE 802.1Q.
•
Each port always belongs to a default VLAN with its port VID (PVID) as an untagged
member. Also, a port can belong to multiple VLANs and be tagged members of these
VLANs.
•
A port must not be a tagged member of its default VLAN.
•
If a non-tagged or null
PVID of the ingress port.
•
If the packet is tagged with non
•
The look up process starts with VLAN look up to determine whether the VID is valid. If the
VID is not valid, the packet will be dropped and its address will not be learned. If the VID is
valid, the VID, destination address, and source address lookups are perfo
•
The VID and destination address lookup determines the forwarding ports. If it fails, the
packet will be broadcasted to all members of the VLAN, except the ingress port.
S957AE-10BTS User Manual
Page 102 of 113
You can setup the bridge parameters in bridge command. If the product is configured as a router,
you do not want to setup the bridge parameters. Move the cursor “
>>
“ to
bridge
Default gateway
Static bridging table
You can setup default gateway IP via gateway command.
You can setup 20 sets of static bridge in static command. After entering
static
Add static MAC entry
Delete static MAC entry
Modify static MAC entry
Show static bridging table
After enter add menu, the screen will prompt as follow
Configure MAC address
Configure LAN interface bridging type
Configure WAN1 interface bridging type
Configure WAN2 interface bridging type
Configure WAN3 interface bridging type
Configure WAN4 interface bridging type
Configure WAN5 interface bridging type
Configure WAN6 interface bridging type
Configure WAN7 interface bridging type
Configure WAN8 interface bridging type
Show static bridging table
Virtual LAN (VLAN) is defined as a group of devices on one or more LANs that are configured so
that they can communicate as if they were attached to the same wire, when in fact they are located
on a number of different LAN segments. Because VLAN is based on logical instead of physical
connections, it is extremely flexible.
The specification of VLAN function is as follow:
The unit supports up to 8 active VLANs with shared VLAN learning (SVL) bridge out of
4096 possible VLANs specified in IEEE 802.1Q.
Each port always belongs to a default VLAN with its port VID (PVID) as an untagged
member. Also, a port can belong to multiple VLANs and be tagged members of these
A port must not be a tagged member of its default VLAN.
tagged or null-VID tagged packet is received, it will be assigned with the default
PVID of the ingress port.
If the packet is tagged with non-null VID, the VID in the tag will be used.
look up process starts with VLAN look up to determine whether the VID is valid. If the
VID is not valid, the packet will be dropped and its address will not be learned. If the VID is
valid, the VID, destination address, and source address lookups are perfo
The VID and destination address lookup determines the forwarding ports. If it fails, the
packet will be broadcasted to all members of the VLAN, except the ingress port.
You can setup the bridge parameters in bridge command. If the product is configured as a router,
bridge
and press enter.
static
menu, the screen
Virtual LAN (VLAN) is defined as a group of devices on one or more LANs that are configured so
when in fact they are located
on a number of different LAN segments. Because VLAN is based on logical instead of physical
hared VLAN learning (SVL) bridge out of
Each port always belongs to a default VLAN with its port VID (PVID) as an untagged
member. Also, a port can belong to multiple VLANs and be tagged members of these
VID tagged packet is received, it will be assigned with the default
null VID, the VID in the tag will be used.
look up process starts with VLAN look up to determine whether the VID is valid. If the
VID is not valid, the packet will be dropped and its address will not be learned. If the VID is
valid, the VID, destination address, and source address lookups are performed.
The VID and destination address lookup determines the forwarding ports. If it fails, the
packet will be broadcasted to all members of the VLAN, except the ingress port.
