SMARTLINK
I&II
MDS921AE-10BTS - MDS
Clear command can clear CRC error count.
Generally, you cannot need to change SNR margin, which range is from 0 to 10. SNR margin is an
index of line connection. You can see the actual SNR margin in STATUS SHDSL. The larger SNR
margin, the better line connection. If you set SNR margin in the field as 2,
will drop and reconnect when the SNR margin is lower than 2. On the other hand, the device will
reduce the line rate and reconnect for better line connection.
SHDSL.bis
You can setup the SHDSL.bis parameters by the command
shdsl.bis and press enter.
>> mode
Configure SHDSL.bis mode
Link
Configure SHDSL.bis link
n*64
Configure SHDSL.bis data rate
type
Configure SHDSL.bis annex type
clear
Clear current CRC error count
margin
Configure SHDSL.bis SNR margin
There are two types of SHDSL.bis mode, STU
office and STU-C customer premise equipment.
Link type will be 2-wire or 4-wire mode according to the product. 4
under 2-wire mode. In 4-wire mode router can operate in Auto Fall Back, Standby or Multi
modes.
2-Wire (only for 4-wire model):
M-Pair
M-Pair (Conexant)
Auto Fall Back
Standby
Multi-link
You can setup the data rate by the multiple of 64Kbps where n is from 3 to 89
There are four types of SHDSL.bis Annex type, Annex
Clear command can clear CRC error count.
Generally, you cannot need to change SNR margin, which range is from 0 to 10. SNR margin is an
index of line connection. You can see the actual SNR margin in STATUS SHDSL.bis. The larger is
SNR margin; the better is line connection quality. If you set SNR margin in the field as 2, the
SHDSL.bis connection will drop and reconnect when the SNR margin is lower than 2. On the ot
hand, the device will reduce the line rate and reconnect for better line connection.
S957AE-10BTS User Manual
Page 100 of 113
Clear command can clear CRC error count.
ly, you cannot need to change SNR margin, which range is from 0 to 10. SNR margin is an
index of line connection. You can see the actual SNR margin in STATUS SHDSL. The larger SNR
margin, the better line connection. If you set SNR margin in the field as 2, the SHDSL connection
will drop and reconnect when the SNR margin is lower than 2. On the other hand, the device will
reduce the line rate and reconnect for better line connection.
You can setup the SHDSL.bis parameters by the command
shdsl.bis
. Move the cursor “
Configure SHDSL.bis mode
Configure SHDSL.bis link
Configure SHDSL.bis data rate
Configure SHDSL.bis annex type
Clear current CRC error count
Configure SHDSL.bis SNR margin
There are two types of SHDSL.bis mode, STU-R and STU-C. STU-R means the terminal of central
C customer premise equipment.
wire mode according to the product. 4-wire product can
wire mode router can operate in Auto Fall Back, Standby or Multi
wire model): 2-wire mode, second pair is disabled
4-wire mode. If one of two pairs fails, all link breaks
4-wire mode. Extended compatibility with Conexant IC
4-wire mode. Two pairs works simultaneously. When one pair fails,
traffic goes through the other pair.
4-wire mode. Only one pair works, another pair is in standby.
When one pair fails, traffic goes through the other pair.
4-wire mode. Each pair is connected to two different devices,
which may be or may not be in same location
You can setup the data rate by the multiple of 64Kbps where n is from 3 to 89
There are four types of SHDSL.bis Annex type, Annex-A, Annex-B, Annex-F, and Annex
Clear command can clear CRC error count.
Generally, you cannot need to change SNR margin, which range is from 0 to 10. SNR margin is an
You can see the actual SNR margin in STATUS SHDSL.bis. The larger is
SNR margin; the better is line connection quality. If you set SNR margin in the field as 2, the
SHDSL.bis connection will drop and reconnect when the SNR margin is lower than 2. On the ot
hand, the device will reduce the line rate and reconnect for better line connection.
ly, you cannot need to change SNR margin, which range is from 0 to 10. SNR margin is an
index of line connection. You can see the actual SNR margin in STATUS SHDSL. The larger SNR
the SHDSL connection
will drop and reconnect when the SNR margin is lower than 2. On the other hand, the device will
. Move the cursor “
>>
“ to
R means the terminal of central
wire product can be worked
wire mode router can operate in Auto Fall Back, Standby or Multi-Link
wire mode. If one of two pairs fails, all link breaks
Extended compatibility with Conexant IC
wire mode. Two pairs works simultaneously. When one pair fails,
wire mode. Only one pair works, another pair is in standby.
raffic goes through the other pair.
wire mode. Each pair is connected to two different devices,
which may be or may not be in same location
You can setup the data rate by the multiple of 64Kbps where n is from 3 to 89.
F, and Annex-G.
Generally, you cannot need to change SNR margin, which range is from 0 to 10. SNR margin is an
You can see the actual SNR margin in STATUS SHDSL.bis. The larger is
SNR margin; the better is line connection quality. If you set SNR margin in the field as 2, the
SHDSL.bis connection will drop and reconnect when the SNR margin is lower than 2. On the other
hand, the device will reduce the line rate and reconnect for better line connection.
