BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 76

Page: 76 / 77

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen |

www.berghof-automation.com

270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx

13.

Appendix

13.1. Information on copyright and software licence

The firmware of the devices contains der free software. Parts of this software are available under the
following OpenSource licences, amongst others:



GNU General Public License (GPL)



GNU Lesser General Public License (LGPL)



Mozilla Public License (MPL)



FreeType License (FTL)

The source code of the free software may be requested from Berghof Customer Service within three
years pf delivery of the device, at cost price.

13.2. List of figures

Fig. 1: Overview DC2115WUX CM (rear view) ............................................................................................... 14

Fig. 2: Overview DC2110W X CM (rear view) ................................................................................................ 15

Fig. 3: Overview ET2115WUX CS (rear view) ................................................................................................ 16

Fig. 4: Overview ET2110W X CS (rear view) ................................................................................................. 17

Fig. 5: Dimensions DC2115WUX CM / ET2115WUX CS ............................................................................... 20

Fig. 6: Installation cut-out DC2115WUX CM / ET2115WUX CS ..................................................................... 21

Fig. 7: Dimensions DC2110W X CM / ET2110W X CS .................................................................................. 22

Fig. 8: Installation cut-out DC2110W X CM / ET2110W X CS ........................................................................ 23

Fig. 9: Insertion into the installation cut-out .................................................................................................... 24

Fig. 10: Mounting the securing clips ............................................................................................................... 25

Fig. 11: Fully tightening the securing clips ...................................................................................................... 25

Fig. 12: Power supply plug X100 .................................................................................................................... 27

Fig. 13: Power supply DC2115 connector X1 with power LED ....................................................................... 28

Fig. 14: Block circuit diagram DC2115WUX CM / DC2110W X CM ............................................................... 29

Fig. 15: Block circuit diagram ET2115WUX CS / ET2110W X CS .................................................................. 30

Fig. 16: Digital inputs and outputs DC2115WUX CM / DC2110W X CM plug connector X1 with LEDs 1 to 8 31

Fig. 17: Circuit diagram of the principles of positive switching output ............................................................ 33

Fig. 18: Circuit diagram of the principles of positive switching input............................................................... 34

Fig. 19: Operating ranges of the digital inputs (type 1/3), negative switching ................................................ 34

Fig. 20: Counter Up/Down or Pulse/Direction ................................................................................................ 35

Fig. 21: Counter with Capture input ................................................................................................................ 36

Fig. 22: Analogue inputs X2 ........................................................................................................................... 37

Fig. 23: example connection: voltage input .................................................................................................... 41

Fig. 24: example connection: temperature measurement .............................................................................. 42

Fig. 25: Ethernet interface X4 ........................................................................................................................ 43

Fig. 26: EtherCAT interface X6 ....................................................................................................................... 44

Fig. 27: USB interfaces X3 and X5 (DC2115) ................................................................................................ 45

Fig. 28: CAN interface X8 .............................................................................................................................. 46

Fig. 29: RS-232 / RS-485 interface X9 ........................................................................................................... 47

Fig. 30: RS-485 switchable terminating resistor ............................................................................................. 47

Fig. 31: login window ...................................................................................................................................... 50

Fig. 32: List of web interface settings ............................................................................................................. 51

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Search results

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM

Reviews:

Brands by name

Popular brands

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Search results

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM

Reviews:

Brands by name

Popular brands