manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Share
Download
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 8

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | 

www.berghof-automation.com

 

270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx 

 

8

 

Design of warnings: 
 

  WARNING 

Optional: 

Other 
Symbols 

Hazard type and source 

Short description and consequences 

 

Preventive measures 

1.3.  Hazard categories and indications 

The following indications are used in the case of warning messages so as to ensure your personal 
safety and avoid any damage to property. 

 

The indications have the following meanings: 

 

 

DANGER 

Serious injury or death 

Non-compliance with the safety features will result in death or serious injury. 

 

Take preventive measures. 

 

  WARNING 

Possible serious injury or death 

Non-compliance with the safety features may result in death or serious injury. 

 

Take preventive measures. 

 

  CAUTION 

Possible minor injuries 

Non-compliance with the safety features may result in minor injuries. 

 

Take preventive measures. 

 

 

NOTE 

Possible damage to property 

Non-compliance with the safety features may result in damage to property. 

 

Take preventive measures. 

 
 

 

 

 

 

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands