manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Share
Download
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 54

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | 

www.berghof-automation.com

 

270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx 

 

54

 

6.2.3.  ET2115WUX CS / ET2110W X CS Configuration 

The device must be connected to the network with the correct settings before it can be used. 
 

 

NOTE 

Damage to property! 

 

Before connecting the power supply, ensure that all cabling and the polarity of all the connections 
are correct. 

 
 
1st 

Supply the device with power (24 V). 

After the start the current network settings are displayed (server IP, IP address and network mask). 
 

 

 

Fig. 37: Start page, with network settings 

2nd 

Press the “Configuration” button. 

A page with further information appears. 
 

 

 

Fig. 38: Information page 

3rd 

Press the “Next” button. 

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands