manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Share
Download
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 13

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | www.berghof-automation.com 
270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx  
 

 

 

13

 

3. 

Product description 

The Dialog Controllers of the B-PRIMIS DC-PRIME product group (DC2110W X CM and 
DC2115WUX CM) are control modules with a display for the control and regulation of automation and 
industrial processes in low-voltage installations in real time. 
 
The CODESYS 3.5 (IEC 61131-3) development environment from 3S-Smart Software Solutions is 
used for programming the device. 
 
The Ethernet Terminals of the B-PRIMIS ET-PRIME product group (ET2110W X CS and ET2115WUX 
CS) are input devices with a display for connection to a control system for machines or systems. The 
terminal shows the CODESYS Web visualisation or CODESYS Target visualisation, irrespective of 
whether the visualisation originates from a Berghof PLC control unit or some other CODESYS control 
unit. 
 
 ET211x Ethernet Terminals can be connected via Ethernet interfaces; DC211x Controllers can be con-
nected via various different interfaces and in addition have their own digital and analogue in-
puts/outputs. 
 
The device connection area for all external connections is located at the rear of the devices. These de-
vices are intended for installation on a flat surface in a pre-prepared installation cut-out. 
All connections are of the plug-in type. 

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands