manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Share
Download
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 60

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | 

www.berghof-automation.com

 

270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx 

 

60

 

6.3.4.  microSD card 

  WARNING 

Serious injury as a result of uncontrolled and unpredictable operational behaviour! 

Inserting or removing the microSD card can result in the device malfunctioning. Failure in electronic con-
trol systems may result in uncontrolled and unpredictable operational behaviour. 

 

Insert or remove a microSD card only when the device is switched off. 

 

 

NOTE 

Loss of data! 

microSD cards do not have their own write protection system. 

 

Ensure that no data is deleted or overwritten by accident. 

 
 

Inserting a microSD card 

1st 

Switch the device off. 

2nd 

Insert the microSD card into the microSD card slot. 

3rd 

Switch the device on again. 

 
The microSD card is now ready for data transfer (read, write and copy). 
Path: /media/sd 
 

 

Max. possible storage capacity: 32 GB. 
The life cycle of the gold-plated contacts is up to 10,000 plugging and unplugging cycles. 
The microSD card drive has a push-in/push-out insertion and ejection mechanism. 
To avoid malfunctions, do not withdraw the microSD card by pulling it. 

 
 

 

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands