manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Share
Download
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 19

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | www.berghof-automation.com 
270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx  
 

 

 

19

 

USB 

The USB host interface allows a wide range of peripherals to be connected to the device. This allows a 
USB stick to be used for updating the application or for downloading data directly. 
 

 

USB sticks with FAT/FAT32 formatting are supported. 
If you require support for other USB formats, please contact our Technical Support. 

 

CAN interface (DC2110W X CM / DC2115WUX CM) 

The device has one standard CAN interface which can be used at speeds up to 1 Mbit/s. 
 

Serial interface (DC2110W X CM / DC2115WUX CM) 

The device has 2 serial ports (1x RS-485; 1x RS-232). 
 

Onboard inputs / outputs (DC2110W X CM / DC2115WUX CM) 

The device incorporates digital inputs / outputs and analogue inputs. 
 

Real-time clock (DC2110W X CM / DC2115WUX CM) 

A software interface permits the current time and date to be set and read on a real-time clock with bat-
tery back-up. 
 

microSD card (DC2110W X CM / DC2115WUX CM) 

The standard commercial microSD card interface (SDHC up to max. 32 GB) allows data to be written 
to memory cards or read from memory cards. 
 

Summary of features 

DC2110W X CM / DC2115WUX CM: 
ARM

®

 CPU with Cortex

TM

-

A9 single-core (800 MHz; optional dual or quad core) 

Program memory and data memory (RAM): 512 MB onboard 
Program memory (flash): 2048 MB on-board 
2 USB host interfaces (USB 2.0) 
Non-volatile memory 100 kB 
2 Ethernet 10/100 Base T interfaces (2nd Interface: EtherCAT master interface) 
1 CAN interface 
2 serial interfaces (1x RS-485; 1x RS-232) 
1 µSD card slot 
Onboard I/O 
Real-time clock 
 
ET2110W X CS / ET2115WUX CS: 
ARM

®

 CPU with Cortex

TM

-

A9 single-core (800 MHz) 

1 USB host interface (USB 2.0) 
1 Ethernet 10/100 Base T interface 

 

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands