manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Share
Download
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 75

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | www.berghof-automation.com 
270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx  
 

 

 

75

 

12. 

Customer services / addresses 

Repairs and corrective maintenance may be carried out only by the manufacturer or authorised cus-
tomer service centres. 

12.1.  Customer service 

Berghof Automation GmbH 
Harretstr. 1 
72800 Eningen 
Germany 
T +49.7121.894-183 
F +49.7121.894-100 
e-mail: [email protected] 
www.berghof-automation.com 

12.2.  Addresses 

CAN in Automation; international manufacturer and user organisation for CAN users in automation: 
CAN in Automation e.V. (CiA) 
Am Weichselgarten 26 
91058 Erlangen 
[email protected] 
www.can-cia.de 
 
EtherCAT Technology Group 
ETG Headquarters 
Ostendstraße 196 
90482 Nuremberg 
[email protected] 
www.ethercat.org 
 
Beuth Verlag GmbH, 10772 Berlin 
or 
VDE-Verlag GmbH, 10625 Berlin 
 
VDE Verlag GmbH, 10625 Berlin 
or 
Internet search: 

www.iec.ch 

 
 

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands