manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Share
Download
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 65

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | www.berghof-automation.com 
270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx  
 

 

 

65

 

9. 

Disposal 

The device contains the following components which need to be disposed of separately: 

 

Metals 

 

Electronic components 

 

Battery 

 
The respective national regulations for disposal of electrical devices in B2B trade are applicable. 
 
The following options are available for disposal of the device: 
 

Disposal by the manufacturer 

Unless agreed otherwise, devices can be sent back for disposal. 
 

Disposal in accordance with regional regulations 

 

Dismantle the device and disassemble it completely into its component parts. 

 

Send the metal parts for metal recycling. 

 

Sort the electronic parts (circuit boards, drives etc.). 

 

Dispose of the electronic scrap in accordance with the national laws and regulations. 

 

Check that the battery is fully discharged. 

 

Dispose of the battery in accordance with the national laws and regulations, via an authorised 
collection point. 

 
 
 

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands