manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Share
Download
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 22

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | 

www.berghof-automation.com

 

270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx 

 

22

 

4.2.  Preparation for installation from the front 

DC/ET2110W X C 

The device is intended for installation from the front into a rectangular cut-out on a panel. The support 
material must be rigid and be from 1 to 3 mm thick. 
 

 

 

Fig. 7: Dimensions DC2110W X CM / ET2110W X CS 

Requirements: 

 

To allow sufficient air circulation, it must be ensured that the device has a clear space of at least 
20 mm all round at the rear. 

 

The max. ambient temperature inside the control cabinet must not exceed 55 °C in operation. 

 

The support material for the installation cut-out must be flat, sufficiently stable, and be from 1 to 3 
mm thick. 

 

 

NOTE 

Damage to the device! 

Installation on uneven support material can lead to mechanical stresses and cracks in the front face or 
malfunctioning of the touch screen. 

 

Make sure that the mounting points of the device are all in a common plane, with no more than max-
imum ±0.5 mm variation. 

 

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands