manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Share
Download
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 12

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | 

www.berghof-automation.com

 

270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx 

 

12

 

2. 

Safety 

Safety-related systems 

The use of PLCs in safety-related systems requires specific measures. Wherever a PLC is to be used 
in a safety-related system, the user must be given comprehensive advice by the PLC manufacturer in 
addition to information on any available standards or regulations regarding safety installations. 

 

Before starting any work on devices, switch off all power feeds, including to peripherals. 

 

Keep all ventilation holes unobstructed. 

 
Failure in certain components in an electronic control system may result in uncontrolled and/or unpre-
dictable operational behaviour. 

 

All types of failure must be considered at the system level and the associated preventative 
measures identified. 

 

If necessary, request information from your automation system provider. 

2.1.  Safety instructions 

The device may be operated only when it is in good working order. Exposed sharp edges pose an inju-
ry risk. 

 

If you discover damage to the front glass of the device, do not continue to operate the device. 
Immediately disconnect it from the power supply. 

 

Working on the device 

Do not start work on the device until all necessary safety precautions have been taken. Take precau-
tions to avoid unforeseeable functional events and movements of the system. 

 

Bring the system into a safe condition. 

 

Switch the system and the device off. 

 

Secure the system against being switched on again. 

 

Disconnect the device from the system. 

 
The casing of the device must not be opened. 

 

If work on the internal parts of the device is necessary, contact the manufacturer (see 
"Addresses"). 

 

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands