manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Share
Download
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 28

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | 

www.berghof-automation.com

 

270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx 

 

28

 

DC2110W X CM / DC2115WUX CM 

 

Connect the power supply to plug X1 according to the following table. 

 

 

 

 

 

Fig. 13: Power supply DC2115 connector X1 with power LED 

Power supply plug X1 

Pin  Designa-

tion 

Assignment 

1…8 

I/O 

digital inputs and outputs (see "Digital inputs and outputs (DC2115") 

9 

L0+ 24 V 

Power supply 24 V DC (

–15 %/+20 %) (internal PLC) 

DC2110W X CM: max. 0.8 A (peak current 1.2 A) 

DC2115WUX CM: max. 0.9 A (peak current 1.2 A) 

10 

L1+ 24 V I/O 

Feed to digital output (max. 2 A for 0.5 A per output) for I/O 

11 

M0 / GND 

– 

12 

L0+ 24 V 

Power supply 24 V DC (

–15 %/+20 %) (PLC internal processing) max. 1.2A 

DC2110W X CM: max. 0.8 A (peak current 1.2 A) 

DC2115WUX CM: max. 0.9 A (peak current 1.2 A) 

 
 
The following counterparts have been tested with the S2C-SMT 3.5 (Weidmüller) connector and are 
approved for use with the device: 

 

B2CF 3.50/12/180 

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands