manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Share
Download
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 45

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | www.berghof-automation.com 
270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx  
 

 

 

45

 

5.2.8.  USB 

Devices with a USB interface can be connected to the USB host port (Rev. 2.0). Suitable USB device 
classes are: 
CODESYS user: only USB stick 
Linux level: USB stick or mouse 
 

 

 

Fig. 27: USB interfaces X3 and X5 (DC2115) 

Assignment of USB interface connectors X3 and X5 (DC2115WUX CM / DC2110W X CM) 

Pin  Assignment 

Pin 

Assignment 

B1 

VCC 

B3 

D+ 

B2 

D

– 

B4 

GND 

 

 

NOTE 

Damage to USB stick and malfunction due to data loss! 

Removing a USB stick while it is still in use and data are being transferred can render the USB stick un-
usable. Open files which can no longer be accessed because the USB stick has been removed can block 
the device. 

 

Therefore ensure that all operations are complete before removing the USB stick. 

 

 

NOTE 

Damage to property and malfunctions due to data loss! 

The USB interface is protected against overloading (> 0.5 A). In the event of a short circuit during opera-
tion, the control unit may trigger a reset of the system. 
Substantial property damage and damage to the USB device may ensue. 

 

Before using a USB device, check carefully its power requirements. 

 

 

NOTE 

Failures and malfunctions will occur if direct connections are made to signal earth! 

 

Use only USB devices that have no direct connection between signal earth and the housing. 

 

 

The USB interface plug is designed to withstand 1,000 plugging and unplugging cycles. 

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands