manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Share
Download
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 36

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | 

www.berghof-automation.com

 

270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx 

 

36

 

Example for a counter: Capture input or counter input 

 

 

 

Fig. 21: Counter with Capture input 

Pin 

Designation 

Pin 

Designation 

C1 

Up, A (CNT0) 

C3 

– 

C2 

Down, B (CNT0) 

C4 

Capture (rise), Z (CNT0) 

 
The counter CNT1 is not available with this configuration. 
 
 

Data for the counting inputs 

 

Counting inputs 

Function 

Value 

Description 

Number of counters 

2 

– 

Signal voltage 

(1): DC 15…28 V 
(0): DC 

–3…3 V 

Pulse width within the valid level for at least 1 µs 

Max. frequency: 

- 

Signal 

- 

Counter 

 

500 kHz 

1 counts/s 

Special installation instructions are applicable to 

100 kHz. At the maximum counting frequency, the 

signal generator must ensure a flank steepness of 

at least 20 V/µs. 

Min. Pulse width 

1 µs 

Per level 

counter resolution 

32 bit 

– 

Internal pull-up 

3 kΩ 

– 

 
 

Installation instructions 

 

Screened cable must be used to connect the counters. 

 

The power supply to the sensor (24 V DC; GND) and the signal must both be within the same 
cable. 

 

The PLC and sensor must be supplied by the same power supply unit. 

 

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands