manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Share
Download
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 49

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | www.berghof-automation.com 
270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx  
 

 

 

49

 

6. 

Operation 

6.1.  Switching on and off 

 

 

NOTE 

Damage or malfunction! 

 

Do not insert, connect, undo or touch any connections whilst the device is in operation. 

 

Before starting any work on the device, switch off all power feeds, including those to any connected 
peripherals (sensors and programmable devices etc. with independent power supplies). 

 

 

NOTE 

Damage to property! 

 

Before connecting the power supply, ensure that all cabling and the polarity of all the connections 
are correct. 

 

Switching on 

The device does not have an on/off switch. The device starts automatically when the system is 
switched on or the power is connected. 
 

Switching off 

The device is switched off when the system is switched off or the power supply is disconnected. 
 
 
 

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands