BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 50

Page: 50 / 77

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen |

www.berghof-automation.com

270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx

6.2. Commissioning the network

6.2.1. DC2115WUX CM / DC2110W X CM web interface

The device must be connected to the network with the correct settings before it can be used.

NOTE

Damage to property!



Before connecting the power supply, ensure that all cabling and the polarity of all the connections
are correct.

1st

Supply the device with power (24 V).
After the start the current IP address and network mask of the device are shown at the top right
of the display.

2nd

Connect the device to a programming computer using a network cable (X4) and network switch.

3rd

Open a web browser on the programming computer.

4th

Enter the IP address of the device into the web browser.

5th

The login screen will appear.

Fig. 31: login window

6th

Use the following user name and password to log into the device:
Name: admin
Password: admin

7th

The web configuration page will be displayed.

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Search results

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM

Reviews:

Brands by name

Popular brands

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Search results

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM

Reviews:

Brands by name

Popular brands