manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Share
Download
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 20

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | 

www.berghof-automation.com

 

270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx 

 

20

 

4. 

Installation 

4.1.  Preparation for installation Front installation 

DC/ET2115WUX C 

The device is intended for installation from the front into a rectangular cut-out on a panel. The support 
material must be rigid and be from 1 to 3 mm thick. 
 

 

 

Fig. 5: Dimensions DC2115WUX CM / ET2115WUX CS 

Requirements: 

 

To allow sufficient air circulation, it must be ensured that the device has a clear space of at least 
20 mm all round at the rear. 

 

The max. ambient temperature inside the control cabinet must not exceed 55 °C in operation. 

 

The support material for the installation cut-out must be flat, sufficiently stable, and be from 1 to 3 
mm thick. 

 

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands