Programming
Bennett HF H35 Instruction Manual
45
6.
Press the [
CANCEL
] button to exit this Menu Code.
Figure 4.24
–
New Decimal Value
MENU CODE 9 - SET A NO FLOW TIME OUT
As a security feature, the dispenser can be programmed to turn off if no flow occurs within a specific amount of time. If the pump
handle is turned on and flow occurs but is stopped, the No Flow Time Out feature prevents delivery after the period of time
programmed has elapsed.
The No Flow Time Out feature is programmable from 0 seconds to 999 seconds (16.6 minutes), or an infinite amount of time
represented by dashes (- - -). The dispenser is shipped from the factory with Menu Code 9 disabled (infinite time).
THE DISPENSER
WILL NOT OPERATE IF ZERO SECONDS (MINUTES) ARE SET!
PROGRAMMING PROCEDURE
After the Menu Code has been accessed, press the
9
button and then the
[
MODE
] button on the keypad. This is the factory default setting. The PPM
display shows the dispenser is in Menu Code 9.
The three dashes indicate the No Flow Time Out amount is an infinite amount
or that Menu Code 9 is disabled.
With this setting, the dispenser’s valves will
remain on indefinitely after the pump handle lever is put in the ON position
and the dispenser is authorized.
Use the
0
through
9
buttons on the keypad to enter a Flow Time Out value in
seconds.
NOTE: If an error is made, press the 0 button until all three digits
are zeros and enter a new number or push the number buttons
until the correct number of seconds appears in the mass display.
When the correct value appears in the mass display, press the [
ENTER]
button to save the selection.
To disable Menu Code 9, press the [
UP ARROW
↑]
button on the keypad
and press the
Enter
button. The mass display returns to three dashes.
Press the [
CANCEL
] button to exit this Menu Code.
NOTE: The no flow timer works with the dispenser in the ready
state (handle up and armed) and in the flow state (handle up and
at least .009 gallons/liters dispensed).
NOTE: If a 0 is entered in this mode the dispenser will turn off the
valves immediately, making it inoperable.
Figure 4.25
–
Default No Flow Timeout
Figure 4.26
–
No Flow Timeout
MENU CODE 11 - SET A MASS ALLOCATION LIMIT
The dispenser can be programmed to stop the flow of fuel at a mass you determine. The dispenser is programmed at the factory
to stop the flow of fuel at 0999 mass units. This is the maximum mass limit that can be set for gallons. The maximum limit for
liters is 9999 mass units. The minimum mass limit is 0001 unit.
THE DISPENSER WILL NOT OPERATE IF A ZERO LIMIT IS SET!
NOTE:
Some control consoles will overwrite the mass allocation limit.
Sale $
1
Kilograms
. 8
. 8
Sale $
N O f l O
Kilograms
1 8 0
C O d E
9
Sale $
N O f l O
Kilograms
-
--
C O d E
9
Summary of Contents for HIGH FLOW H35
