Belarus 1822.3 Operator'S Manual Download

Page: 201 / 358

2022.3-0000010 OM

200

5.4.4 Drawbar hitch DH-2R

Figure 5.4.3 – Installation variants scheme of DH -2R

Table 5.5 – Basic parameters and coupling dimensions of DH -2R

Standard size (configuration)

DH -2R (python)

1 Mounting location

Rear lifting device

2 Design features

Cantilever fitted connection pin, verti-
cally adjustable

3 Purpose

For coupling of semitrailed imple-
ments, and implements of tractor semi-
trailer types having also hitch clevis

4 Distance between PTO shaft end extension and
connection pin axis, mm

108

5 Connecting pin diameter, mm

6 Vertical load on DH in hitch point, kN, not more
than

7 Protective mean type

Safety chain (rope)

8 Connection point of a protective mean to the
tractor

Lifting device bore

____________________________________________________________________________________________________________

Implement accessory.

ATTENTION: IT IS FORBIDDEN TO PUT THE DEVICE TO A LOWERMOST PO-

SITION, WHERE IT OVERHANGS THE DH SUPPORTING BRACKET END!

https://tractormanualz.com/

Summary of Contents for 1822.3







































































































































































































































































































































































Search results

Summary of Contents for 1822.3

Reviews:

Related manuals for 1822.3

Brands by name

Popular brands

Belarus 1822.3, Operator'S Manual

Search results

Summary of Contents for 1822.3

Reviews:

Related manuals for 1822.3

Brands by name

Popular brands