manualshive.com logo in svg

Belarus 1822.3, Operator'S Manual

Get your hands on the Operator's Manual for Belarus 1822.3, a must-have for every proud owner. Download this essential manual for free and unlock the full potential of your Belarus 1822.3. Visit our website to access the manual instantly and maximize your product experience.

Share
Download
background image

2022.3-0000010  OM

13

1 TRACTOR DESCRIPTION AND OPERATION

1.1 Tractor assignment

The

tractor “BELARUS-1822.3/1822 .3/2022.3/2022 .3” is intended for perform-

ance of various general –purpose agricultural operations, for basic and preseeding treat-
ment of soil, planting of crops and other cultures in a structure with wide-span and com-
bined units, for harvesting operations in a structure with heavy-duty harvesting complexes
that are designed for forage conservation, crop harvesting, for transport and loading op-
erations.

Low-speed version of the reverse configuration 2022 .3 – 17/32 of BELARUS-

2022 .3 tractor is also intended to operate with units that have active working elements
driven from the rear PTO and move at low operating speeds.

The version 2022 .3 – 17/32 has the following differences from the basic version:

- the reduced speed range of the front travel includes the speeds of 1,14 km/h to

24,32 km/h;

- the speed range of the reverse travel includes the speeds of 1,60 km/h to 11,46

km/h;

- to increase the clearance a smaller fuel tank is mounted under the lateral fuel tank;
- there is a protection for the rear glass and lights;
- rear wheels have protected valves.

The

tractor “BELARUS-1822.3/2022.3” is a general-purpose wheeled tractor of trac-

tion class 3 with the wheel formula 4X4.

The

tractor “BELARUS-1822.3/2022 .3” is a general-purpose wheeled tractor of

traction class 3 with the wheel formula 4X4  and a reversible control post.

Distinctive features of BELARUS-1822.3/1822 .3 model compared to BELARUS-

2022.3/2022 .3 model are listed in table 1.1.

BELARUS-1822.3/1822 .3

BELARUS-2022.3/1822 .3

Engine  -260.9S2,

rated power 132,5 kW

Engine D-260.4S2,

rated power 156 kW

Ballast 1822.3-4235010 (without weights)

Ballast weight 2022-4235010 (with

weights)

The rear PTO has only standard

operation mode, the economy mode is
missing

The rear PTO has both standard

and economy operation modes

Supplementary ballast

2022-4235025-  is missing

Supplementary ballast

2022-4235025-  is installed on order

Front lift linkage and front PTO are

not mounted

Front lift linkage and front PTO are

not mounted on order

Set for rear wheel twinning is sup-

plied on order

Set for rear wheel twinning is in-

cluded into basic configuration

Appearance of BELARUS-1822.3/1822 .3 tractor and BELARUS-

2022.3/2022 .3 tractor with basic configuration is shown in figure 1.1.1.

Appearance of BELARUS-2022.3/2022 .3 equipped with front PTO and FLL is

shown n figure 1.1.2.

https://tractormanualz.com/

Summary of Contents for 1822.3







































































































































































































































































































































































Reviews:

No comments

Related manuals for 1822.3

MacDon M155 Manual preview
M155
Brand: MacDon Pages: 2
Curtis 1JD2520AS Installation Instructions Manual preview
1JD2520AS
Brand: Curtis Pages: 16
Allis-Chalmers G Service Manual preview
G
Brand: Allis-Chalmers Pages: 45
Zetor COMPAX CL 25 NC Operator'S Manual preview
COMPAX CL 25 NC
Brand: Zetor Pages: 108
Zetor 10641 Forterra turbo Operator'S Manual preview
10641 Forterra turbo
Brand: Zetor Pages: 315
Montgomery Ward ZYJ-1433A Owner'S Manual And Parts List preview
ZYJ-1433A
Brand: Montgomery Ward Pages: 18
Allis-Chalmers 910-6 Speed Owner'S Manual preview
910-6 Speed
Brand: Allis-Chalmers Pages: 48

Brands by name

Popular brands

Load more brands