manualshive.com logo in svg

Belarus 1822.3, Operator'S Manual

Get your hands on the Operator's Manual for Belarus 1822.3, a must-have for every proud owner. Download this essential manual for free and unlock the full potential of your Belarus 1822.3. Visit our website to access the manual instantly and maximize your product experience.

Share
Download
background image

2022.3-0000010  OM

120

3.11 Front driving axle

3.11.1 General information

The front driving axle is intended for torque transfer from the engine to front driving

wheels of the tractor. The front driving axle consists of one-piece cast axle beam 3 (figure
3.11.1), a central reduction unit 4 with a main drive and a differential, attached to the FDA
beam with the bolts, final drive reduction units 1, 7, connected with the axle beam by
means of kingpin spindle 2. Turning of the wheel hub drives is controlled by a steering rod
5, linked with the cases of the final drive reduction units by means levers 6.

1, 7 – left final drive reduction unit; 2 – kingpin spindle; 3 – frond driving axle beam; 4 –

central reduction unit; 5 – steering rod; 6 – lever.

Figure 3.11.1 – Front driving axle

3.11.2 Central reduction unit

A housing 5 (figure 3.11.2) of the central reduction unit is attached to the FDA beam with

bolts. The housing includes bevel gears 12, 25 of the main drive and a limited-slip self-locking dif-
ferential, including axle shaft gears 23, differential cages 15, disks 16, 17, pinions 21, pinion
shafts 20, mounted in cases 13, 14, braced with bolts 11. The self-locking differential connects
automatically both axle shafts 9, 22 into one piece at separated skidding of the front wheels. Un-
der the influence of axial forces the cages 15 compress the disks 16, 17, bringing the axle shaft
gears in contact with the differential cases. The differential gets locked at linear movement. As the
tractor turns, outer forces exceed friction in the disks, that skid and the differential gets unlocked.

Preload of the drive gear 25 tapered bearings 2, 4 shall make 0.01 to 0.04 and is adjusted

by matching spacer rings 3 and tightening a nut 1 with a torque of 120 to 150 Nm. The preload
shall correspond to the antitorque moment of the drive gear (without collars 26 installed) of 0.2 to
1.4 Nm.

Preload of 0.01 to 0.08 Nm in bearings 6, 24 of the differential and clearance of 0.18 to

0.25 Nm in the meshing of gears of the main drive 12, 25 are adjusted by nuts 7, 19 with lock
plates 18 and by bolts 10. The total antitorque moment with due account for preload in the bear-
ings of the gear 25 shall make 0.8 to 7.4 Nm.

Adjustments of the central reduction unit of the FDA are complicated operations and must

be performed by dealers only.

https://tractormanualz.com/

Summary of Contents for 1822.3







































































































































































































































































































































































Reviews:

No comments

Related manuals for 1822.3

Murray 40508x92G Instruction Book preview
40508x92G
Brand: Murray Pages: 52
AVANT A440586 Operator'S Manual For Attachment preview
A440586
Brand: AVANT Pages: 24
Ventrac 4500P Operator'S Manual preview
4500P
Brand: Ventrac Pages: 87
PRONAR PRONAR 5110 Operator'S Manual preview
PRONAR 5110
Brand: PRONAR Pages: 122
Cadet CLT-542H Operator'S Manual preview
CLT-542H
Brand: Cadet Pages: 88
Cub Cadet 8354 Service Manual preview
8354
Brand: Cub Cadet Pages: 289
AVANT Robot 185 Operator'S Manual preview
Robot 185
Brand: AVANT Pages: 76
TARAL 850 Instruction Manual preview
850
Brand: TARAL Pages: 102
Geax EK75CFAJ160 Operation And Safety Manual preview
EK75CFAJ160
Brand: Geax Pages: 77
Kubota AP-SG2572 Operator'S Manual preview
AP-SG2572
Brand: Kubota Pages: 28
Kubota LA1154A Assembly Instructions Manual preview
LA1154A
Brand: Kubota Pages: 107
Kalmar TL2 Maintenance Manual preview
TL2
Brand: Kalmar Pages: 216
Yanmar EB3100 Operator'S Manual preview
EB3100
Brand: Yanmar Pages: 164
Simplicity 7000-6 Speed Series Operator'S Manual preview
7000-6 Speed Series
Brand: Simplicity Pages: 34
Simplicity 1690431 Operator'S Manual preview
1690431
Brand: Simplicity Pages: 38
Simplicity Yeoman 578 Operator'S Manual preview
Yeoman 578
Brand: Simplicity Pages: 40
Maschio TORO RAPIDO Use And Maintenance preview
TORO RAPIDO
Brand: Maschio Pages: 108
Hurricane 10577RB Instruction Manual preview
10577RB
Brand: Hurricane Pages: 96

Brands by name

Popular brands

Load more brands