manualshive.com logo in svg

Belarus 1822.3, Operator'S Manual

Get your hands on the Operator's Manual for Belarus 1822.3, a must-have for every proud owner. Download this essential manual for free and unlock the full potential of your Belarus 1822.3. Visit our website to access the manual instantly and maximize your product experience.

Share
Download
background image

2022.3-0000010  OM

233

5.15.3 Information about mounting holes

In the present subsection data on availability of mounting holes of tractor which can

be used by manufacturers of front loaders for loader installation, and also by manufacturer
of tractors for installation of various equipment are set forth. The mounting holes arrange-
ment scheme for tractor “BELARUS-1822.3/1822 .3/2022.3/2022 .3” is shown in Figure
5.15.2. Parameters of mounting holes are listed in Table 5.15.

Table 5.15 – Parameters of mounting holes of tractor “BELARUS-

1822.3/1822 .3/2022.3/2022 .3”

Denomination

 1

 2

 3

 4

 5

Diameter **

16-7H

16-7H

16-7H

18

16-6H

Length

22

10

10

13,5

14

Denomination

 6

 7

 8

 9

 10

Diameter **

16-6H

16-6H

16-6H

16-6H

16-6H

Length

14

14

14

14

14

Denomination

 11

 12

 13

 14

 15

Diameter **

16-6H

16-6H

16-6H

16-6H

16-6H

Length

14

14

14

14

14

Denomination

 16

 17

 18

 19

 20

Diameter **

16-6H

18

18

18

18

Length

28

8

8

8

8

Denomination

 21

 22

 23

 24

 25

Diameter **

18

18

18

18

18

Length

8

8

8

8

8

Denomination

 26

 27

 28

 29

 30

Diameter **

18

16-7H

16-7H

16-7H

16-7H

Length

8

18

18

18

23

Denomination

 31

 32

 33

 34

 35

Diameter **

16-7H

16-7H

16

16

20

Length

23

23

12

12

13,5

Denomination

 36

 37*

 38*

 39*

 40*

Diameter **

20

18

18

22 1,5-6h  22 1,5-6h

Length

13,5

13,5

13,5

50

50

Denomination

 41*

 42*

 43*

 44*

 45*

Diameter **

22 1,5-6h  22 1,5-6h

10

10

20

Length

50

50

15

15

32

Denomination

 46*

 47*

 48*

 49*

 50*

Diameter **

20

20

20

20

20

Length

32

32

32

16

40

Denomination

 51*

 52*

 53*

 54*

Diameter **

20

20

20

20

Length

40

40

28

28

___________________________________________________________

* Bottom hole
** Thread parameters for a screw hole.

NOTES:

Sizes in Table 5.15 are given in mm.
Holes  1…26 , 38…49  –  right and left.
Holes  49, 53   54  –  for installation of pins.
Holes  1…31 (odd numbers) – upper row.
Holes  2…32 (even numbers) – low row.
In course of mounted components installation ensure safety of bushings in holes 1, 6 and 14. It is not
recommended to use holes with bushings meant for coupling.

ATTENTION: IT IS NOT RECOMMENDED TO USE SIDE HOLES WITH BUSHINGS!

MOUNTED LOADER COMPONENTS SHOULD NOT CAUSE BUSHING DESTRUCTION!

https://tractormanualz.com/

Summary of Contents for 1822.3







































































































































































































































































































































































Reviews:

No comments

Related manuals for 1822.3

Glasdon NEXUS 36G Manual preview
NEXUS 36G
Brand: Glasdon Pages: 2
Daedong KIOTI EX35 Manual preview
KIOTI EX35
Brand: Daedong Pages: 238
Kverneland A136138200 User Manual preview
A136138200
Brand: Kverneland Pages: 74
Ventrac 3000 Owner'S/Operator'S Manual preview
3000
Brand: Ventrac Pages: 33
Halo COMPACTOR SENSOR TRASH CAN User Manual preview
COMPACTOR SENSOR TRASH CAN
Brand: Halo Pages: 7
Ransomes CT325 Operator Instructions Manual preview
CT325
Brand: Ransomes Pages: 72
Femco WEATHERBRAKE 307022172 Instructions Manual preview
WEATHERBRAKE 307022172
Brand: Femco Pages: 7
ACF TRASH GUARD PLUS Quick Start Manual preview
TRASH GUARD PLUS
Brand: ACF Pages: 2
GE UCG1680 Owner'S Manual preview
UCG1680
Brand: GE Pages: 24
Bonatti LSN 1250 Operation And Maintenance Manual preview
LSN 1250
Brand: Bonatti Pages: 23
Midwest BB20-48 Operation And Parts Manual preview
BB20-48
Brand: Midwest Pages: 8
Mikasa 450125 Operating Instructions Manual preview
450125
Brand: Mikasa Pages: 30
Cub Cadet LT1040 LE Operator'S Manual preview
LT1040 LE
Brand: Cub Cadet Pages: 32
Cub Cadet Z-Force S 54 Operator'S Manual preview
Z-Force S 54
Brand: Cub Cadet Pages: 36

Brands by name

Popular brands

Load more brands