Home
/
Belarus
/
1822.3
/
Operator'S Manual

Belarus 1822.3, Operator'S Manual, Page: 169 / 358

Share

Page: 169 / 358

Belarus 1822.3 Operator'S Manual Download Page 169

2022.3-0000010 OM

168

Before starting to move define a necessary speed of tractor movement. The speed

diagram of the tractor “BELARUS-1822.3/1822 .3/2022.3/2022 .3” with tires of basic con-
figuration is given in the instruction table attached to the right glass of the cab and also in
subsection 2.13.2. “Tractor velocity diagram”.

To put the tractor in motion the following shall be done:
- reduce engine speed;
- depress the clutch pedal;
- set a required gearbox range using the range shifting lever as per the range shifting dia-

gram;

- if required, press the button of the reduction unit higher pass (H). Hereby a LED

lamp of red color will light up on the speed and pass shifting handle, and also the higher
pass annunciator will light up on the control panel of the rear axle DL, FDA drive and
FPTO drive (if installed), informing that a higher pass of the reduction unit is engaged;

- set a desired speed, for this shift the speed and pass shifting lever from neutral

(“N”) into any of positions 1, 2, 3, 4, 5, 6, as per the speed shifting diagram;

- disengage the parking break, slowly release the clutch pedal, increasing at the

same time fuel feed. The tractor will start moving.

IT IS FORBIDDEN TO START MOVEMENT WITH BIG TRACTION LOAD!

IT IS FORBIDDEN TO MOVE THE TRACTOR WITH THE DOOR OPEN!

ATTENTION: SHIFT RANGES, REDUCTION PASSES AND SPEEDS ONLY WITH

THE TRACTOR STOPPED AND THE CLUTCH PEDAL FULLY DEPRESSED! PER-
FORMING TRANSPORT OPERATIONS IT IS PERMITTED TO SHIFT SPEEDS WITHIN
A RANGE DURING TRAVEL. THE SHIFTING SHALL BE CARRIED OUT AS THE TRAC-
TOR COASTS AND THE CLUTCH PEDAL FULLY DEPRESSED!

ATTENTION: THE REDUCTION PASSES “L” AND “H” CAN BE ENGAGED ONLY

AFTER THE SPEED SHIFTING LEVER IS SET INTO NEUTRAL POSITION!

ATTENTION: DON’T HOLD THE FOOT ON THE CLUTCH PEDAL DURING TRAC-

TOR OPERATION, BECAUSE IT CAN LEAD TO CLUTCH SLIPPING, ITS OVERHEATING
AND FAILURE!

ATTENTION: TO ENGAGE THE SPEED SMOOTHLY, WITHOUT SHARP

PUSHES, MOVE THE SPEED AND PASS SHIFTING LEVER ACCORDING TO THE DI-
GRAM AND HOLD IT PRESSED UNTIL THE SPEED IS FULLY ENGAGED!

ATTENTION: STARTING TO MOVE, MAKE SURE THE PARKING BRAKE IS

DISENGAGED!

ATTENTION: WITH THE DIFFERENTIAL LOCK ENGAGED THE TRACTOR

MOVEMENT SHALL NOT EXCEED 13 KM/H!

ATTENTION: OPERATING ON ROADS WITH HARD SURFACE IT IS NECES-

SARY TO SWITCH THE FDA DRIVE OFF TO AVOID INCREASE WEAR OF FRONT
WHEELS!

ATTENTION: IT IS ALLOWED TO USE THE ENGINE AT FULL LOAD ONLY

WHEN THE COOLANT TEMPERATURE REACHES 70°C.

https://tractormanualz.com/

«
...
167
168
169
170
171
...
»

Summary of Contents for 1822.3







































































































































































































































































































































































Reviews:

No comments