Belarus 1822.3 Operator'S Manual Download | Manualshive

Page: 184 / 358

background image

2022.3-0000010 OM

183

Do not work under raised agricultural implements. Do not leave implements uplifted

when stopping for a long time.

Before lifting and lowering a hinged agricultural implement and also when turning

the tractor make sure there is no danger of catching somebody or stumbling on the hurdle.

The mounted and semi-mounted machine is to be lowered into its operating position

and up lifted into the hauling position only with a straight-line motion of the assembly unit.

To avoid breakdown of the tractor or the agricultural implement, drive and turn the

tractor assembly with the agricultural implement uplifted only after you make sure the front
and rear PTOs are disengaged.

Linking and hinging the agricultural machines and implements on the tractor the

rear operator shall stay at a safety distance until the operation is fully stopped. The linkage
(hinge) shall be started only after the tractor operator gives a command.

Engaging the rear PTO move the control rod smoothly from “off” position to “on” po-

sition, in order to avoid breakdown of the drive shaft, gears of the gear group and the rear
PTO end extension.

Linking the machine cardan shaft to the RPTO, disengage the RPTO, stop the trac-

tor by means of the parking brake and stop the engine.

After disconnecting the machines driven by the rear or the front PTO, remove car-

dan drives and cover the PTO end extensions with protective caps.

Cardan shafts, transferring torque from the front and rear PTOs of the tractor to the

implement working units shall be safeguarded.

Operating with stationary machines, driven by the front and rear PTOs, always en-

gage the parking brake and lock the rear wheels at the front and at the back. Make sure
the machine is securely fixed.

Make sure the safeguards of the front and rear PTOs are mounted and, if the PTO

is not used, put back the cap of the PTO shaft end extension.

Do not wear loose clothes when working with the front and rear PTOs or near rotat-

ing equipment.

To avoid breakdown of the tractor or the agricultural machine, turning the tractor as-

sembly is possible only after the working units of the machine have been fully raised from
the ground.

When the tractor assemblies are operating in a column, they shall have an interval

not less than 30 m between each other.

Depending on operation conditions use natural ventilation of the cab or the unit of

air cooling and heating.

During tractor operation the operator shall use standard means of protection for hearing

organs.

In case the tractor assembly is operated or is driven in an area of power transmis-

sion lines, a distance between the top of the tractor assembly and wires shall conform to
table 4.8.

Table 4.8

Line voltage, V, up to

11 20-25 110 154-220 330-500

Horizontal distance, m, not less than

1,5

2

4

6

9

Vertical distance, m, not less than

1

2

3

4

6

https://tractormanualz.com/

«
...
182
183
184
185
186
...
»

Summary of Contents for 1822.3







































































































































































































































































































































































Reviews:

No comments

Related manuals for 1822.3

Brand: wsm Pages: 303

Brand: wsm Pages: 619

Jinma 200 Series

Brand: Yancheng Tractor Factory Pages: 52

Brand: Daedong Pages: 196

Brand: Degelman Pages: 31

Brand: GE Pages: 28

Brand: LS Pages: 158

Brand: Husqvarna Pages: 60

Brand: Woods Pages: 22

Brand: Hitech Pages: 24

52-143-380201-00

Brand: Classic Accessories Pages: 2

Brand: Kubota Pages: 205

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands