Bay Networks 58000 Installation And Reference Manual Download Page 98 | Manualshive

Page: 98 / 158

background image

Installing and Removing the Model 58000 Switch

4-8

893-878-B

Removing the Model 58000 Switch

To remove the switch from the Model 500x chassis, follow these steps:

1.

Use a flat-tip screwdriver to loosen the four captive retaining screws
that secure the switch to the chassis.

These screws are spring-loaded to pop outward when they are unscrewed
from the chassis. The screws are held in place on the switch front panel by
locking washers.

2.

Rotate the top and bottom inserter/extractor levers away from the
center of the switch front panel to release the switch from the
backplane connector.

3.

Slide the switch out of the chassis (see

Figure 4-4.

Removing the switch

Hold the front panel with one hand while you support the bottom of the
switch with the other hand.

4.

Install two filler panels on the chassis slots to maintain the cooling air
flow within the chassis.

CAUTION:

Removing a switch that is connected to other switches in a switch

community affects all switches in the community. All other switches will
transition to a configuring mode. During this time, the switches will not
forward any frames.

Model 5000

6181

Inserter/extractor
lever

Captive retaining
screw

893-878-B Book Page 8 Monday, May 12, 1997 2:06 PM

«
...
96
97
98
99
100
...
»

Summary of Contents for 58000































































































































































Reviews:

No comments

Related manuals for 58000

Brand: A10 Pages: 52

Brand: NetComm Pages: 3

Brand: Allied Telesis Pages: 22

Brand: Watchguard Pages: 40

Brand: Patton electronics Pages: 12

Brand: Kanguru Pages: 13

Brand: Connectland Pages: 10

Brand: US Robotics Pages: 180

Brand: Comtrend Corporation Pages: 4

Brand: Linksys Pages: 6

Brand: MaxComm Pages: 10

Brand: iNetVu Pages: 20

Brand: ZyXEL Communications Pages: 12

Brand: M-system Pages: 4

Brand: Kramer Pages: 56

Brand: Kasda Pages: 39

Brand: Planet Pages: 54

Brand: Cradlepoint Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands