Bay Networks 58000 Installation And Reference Manual Download Page 132

Page: 132 / 158

Configuring the Model 58000 Switch

6-26

893-878-B

Displaying and Modifying the Expansion Module Port Configuration

The Modifying Expansion Module Port Configuration menu option is provided
only when an expansion module is installed in the Model 58000 switch.You
can modify expansion module port duplex mode, port type, and port flow
control from this menu.

To display the Modify Expansion Port Configuration menu, follow these steps:

Choose Configuration Parameters from the Main Menu.

The Configuration Parameters menu is displayed.

Choose Switch Parameters from the Configuration Parameters menu.

The Switch Parameters menu is displayed.

Choose Modify Expansion Module Port Configuration from the
Switch Parameters menu.

A Modify Expansion Module Port Configuration menu similar to that
shown in

Figure 6-13

is displayed.

Figure 6-13. Modify Expansion Module Port Configuration menu

Bay Networks 58000 Ethernet Switch Module

System Up Time: 1 D-12H-22M-11S IP Address: 134.177.32.98(M)

MAC Address: 000081000201 Default Gateway: 134.177.32.1

Switch Software Version: 1.4.3 Subnet Mask: 255.255.255.0

Expansion Module Port Configuration

Expansion Card Port Speed and Duplex Mode

Expansion Card Port Type

Expansion Card Port Flow Control

Change Expansion Card port speed and duplex mode.

Use cursor keys to choose item. Press <RETURN> to confirm choice.

<CTRL><P>: Main Menu <CTRL><U>: Previous Menu <CTRL><L>: Refresh Screen

893-878-B Book Page 26 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands