Bay Networks 58000 Installation And Reference Manual Download Page 46 | Manualshive

Page: 46 / 158

background image

Planning a Switched Network

2-8

893-878-B

Model 58000 Switch Operation

This section discusses the operation of the Model 58000 switch within switch
communities and covers the following topics:

•

MDA port and cable options

•

Link speeds

•

Full-duplex operation

•

Flow control

•

Model 58000 switch address tables and limitations

•

Configurable port type feature

MDA Port and Cable Options

Before connecting network devices to the Model 58000 switch, determine the
type(s) of MDA(s) you need to install in the switch. Also decide what type of
cable to use to connect these devices.

When connecting network devices to the Model 58000 switch, always observe
the maximum segment length allowed by the IEEE 802.3 10BASE-T and
100BASE-T standards.

shows the MDA options, cable options, and maximum segment

lengths for the Model 58000 switch. Refer to the IEEE 802.3 10BASE-T and
100BASE-T standards for more information about cable options and maximum
segment lengths for 10 Mb/s and 100 Mb/s signals.

NOTE:

English and metric measurements given in

are rounded to

the nearest foot or meter.

893-878-B Book Page 8 Monday, May 12, 1997 2:06 PM

«
...
44
45
46
47
48
...
»

Summary of Contents for 58000































































































































































Reviews:

No comments

Related manuals for 58000

Power Xpert Meter 2000

Brand: Eaton Pages: 16

POW-R-COMMAND 1000

Brand: Eaton Pages: 84

Brand: Garmin Pages: 2

Brand: H3C Pages: 16

Brand: H3C Pages: 24

Brand: Nayar Systems Pages: 37

Hollywood DV-Bridge

Brand: Dazzle Pages: 63

Brand: Watchguard Pages: 40

Brand: Kontron Pages: 42

Brand: NETGEAR Pages: 142

Brand: ADTRAN Pages: 161

Brand: Digi Pages: 75

Ultra WiFi Booster

Brand: Optus Pages: 8

SteelCentral NetExpress 470

Brand: Riverbed Pages: 140

Brand: PairGain Pages: 48

LS-5100-16P-SI-OVS-H3

Brand: H3C Pages: 313

Brand: TP-Link Pages: 2

ICPE2600 Series

Brand: 3onedata Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands