Bay Networks 58000 Installation And Reference Manual Download Page 47 | Manualshive

Page: 47 / 158

background image

Model 58000 Switch Operation

893-878-B

2-9

Table 2-1.

Model 58000 switch MDA and cable options

MDA or
built-in port

Number
and type
of ports

Port
speed

Cable
options

Maximum segment length

10BASE-T port

16 RJ-45

10 Mb/s

Category 3, 4, or
5 UTP

328 ft (100 meters)

100BASE-FX
MDA port

Two SC

100 Mb/s

62.5/125 micron
multimode fiber optic or
50/125 micron
multimode fiber optic

1352 ft (412 meters) between
ports operating in the half-duplex
mode or up to 6562 ft (two
kilometers) between ports
operating in the full-duplex mode.
Note: For more information about
100BASE-FX port specifications,
refer to

, “Technical

Specifications” of

Installation and

Reference for the Model
58000-1xx Media Dependent
Adapters.

100BASE-TX
MDA port

Two RJ-45

100 Mb/s

Category 5 UTP

328 ft (100 meters)

100BASE-FX/TX
MDA ports

One SC

100 Mb/s

62.5/125 micron
multimode fiber optic or
50/125 micron
multimode fiber optic

1352 ft (412 meters) between
ports operating in the half-duplex
mode or up to two kilometers
between ports operating in the
full-duplex mode.
Note: For more information about
100BASE-FX port specifications,
refer to

, ” Technical

Specifications” of

Installation and

Reference for the Model
58000-1xx Media Dependent
Adapters.

One RJ-45

100 Mb/s

Category 5 UTP

100 meters

893-878-B Book Page 9 Monday, May 12, 1997 2:06 PM

«
...
45
46
47
48
49
...
»

Summary of Contents for 58000































































































































































Reviews:

No comments

Related manuals for 58000

Brand: Watchguard Pages: 39

Brand: Javad Pages: 35

Brand: Draytek Pages: 8

Brand: Konica Minolta Pages: 38

Brand: Western Digital Pages: 8

Brand: Lanner Pages: 109

Brand: Vaisala Pages: 32

HomePlug AV Ethernet Bridge PLE0200

Brand: Abocom Pages: 2

Brand: Davey Pages: 18

Brand: Schrack Technik Pages: 2

Brand: TP-Link Pages: 57

Brand: JLCooper Electronics Pages: 12

Brand: ZyXEL Communications Pages: 66

Brand: Alfa Network Pages: 11

Brand: Comelit Pages: 140

TigerSwitch 100 SMC6924VF

Brand: SMC Networks Pages: 174

TeraStation WSS WS5020N6

Brand: Buffalo Pages: 115

Brand: Pro-Nets Technology Corporation Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands