Bay Networks 58000 Installation And Reference Manual Download Page 145

Page: 145 / 158

893-878-B

A-1

Appendix A Technical Specifications

This appendix lists technical specifications and includes a declaration of
conformity for the Model 58000 switch.

General Specifications

Network Protocol and Standards Compatibility

IEEE 802.3i 10BASE-T

IEEE 802.3u 100BASE-T

Data Rate and Encoding

Built-in ports:

10 Mb/s Manchester Encoding for 10BASE-T

MDA ports:

100 Mb/s with 4B5B encoding and
MLT-3 physical interface for 100BASE-TX

100 Mb/s with 4B5B encoding and
NRZI physical interface for 100BASE-FX

Interfaces

Built-in ports:

RJ-45 connectors for 10BASE-T ports

MDA ports:

RJ-45 connectors for 100BASE-TX MDA ports

SC fiber optic connectors for 100BASE-FX MDA ports

Electrical Specifications

Power consumption:

Without MDA:

60W @ -48VDC

With MDA:

78W @ -48VDC

Thermal rating:

Without MDA:

205 BTU/Hr.

With MDA:

266 BTU/Hr.

893-878-B Book Page 1 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands