Bay Networks 58000 Installation And Reference Manual Download Page 26

Page: 26 / 158

Overview of the Model 58000 10/100 Ethernet Switch

1-4

893-878-B

•

Smart-swap capability, in which the configuration information from a
replaced module is automatically downloaded to the replacement module

•

Management by Bay Networks Optivity LAN 7.0 (or later) for UNIX and
Optivity Campus 6.0 (or later) for Windows network management
software

•

Configuration and status reporting through front-panel LED display and
System 5000 service port, and remotely through SNMP

•

Internal throughput of up to 2 Gb/s

•

Support for dedicated end stations (single address/port) and shared-media
LAN segments (multiple address/port)

•

Redundant link capability for network fault tolerance

•

Compatibility with the Model 28115 LattisSwitch and the Model 28104
LattisSwitch, including virtual LAN support using Optivity network
management software (For more information about virtual LANs, see

Network Performance Improvement

in Chapter 2,

Planning a Switched

Network

•

Support for connections to the Model 3328 Ethernet Switching Engine,
the BayStack Ethernet Workgroup Switch, and the Centillion 100 switch

•

Advanced agent level network management support for the System 5000
Model 53xx Ethernet host modules

893-878-B Book Page 4 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands