Bay Networks 58000 Installation And Reference Manual Download Page 136

Page: 136 / 158

Configuring the Model 58000 Switch

6-30

893-878-B

Figure 6-16. Expansion Module-Switch Port Flow Control menu

Choose the port you want to change.

The system displays the current flow control setting for that port and
prompts you to change the setting. The current flow control setting is
highlighted and the other flow control option is displayed unhighlighted.

Select the new flow control option, either enable or disable.

The system prompts you for confirmation. The modified ports use the new
port flow control settings immediately.

Repeat steps 2 and 3 for additional ports.

Bay Networks 58000 Ethernet Switch Module

System Up Time: 1 D-12H-22M-11S IP Address: 134.177.32.98(M)

MAC Address: 000081000201 Default Gateway: 134.177.32.1

Switch Software Version: 1.4.3 Subnet Mask: 255.255.255.0

Expansion Module-Switch Port Flow Control

Port Flow Control

MDA1 P1 [Enable]

MDA1 P2 [Enable]

MDA2 P1 [Enable]

MDA2 P2 [Enable]

MDA3 P1 [Enable]

MDA3 P2 [Enable]

MDA4 P1 [Enable]

MDA4 P2 [Enable]

Enable/Disable MDA Port Flow Control

Use cursor keys to choose item. Press <RETURN> to confirm choice.

<CTRL><P>: Main Menu <CTRL><U>: Previous Menu <CTRL><L>: Refresh Screen

893-878-B Book Page 30 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands