Bay Networks 58000 Installation And Reference Manual Download Page 117

Page: 117 / 158

Using the System Configuration Menus

893-878-B

6-11

Displaying Local Virtual LAN Information

If virtual LANs are defined as part of the Model 58000 switch, the switch mode
is automatically displayed as virtual mode.

To display the virtual LAN information for the Model 58000 switch, choose
Switch Mode from the System Information screen. A Local VLAN Information
screen similar to that in

Figure 6-5

is displayed.

Figure 6-5.

Local VLAN Information

NOTE:

Use Optivity network management software to configure virtual LANs.

For more information, refer to the user documentation that shipped with your
Optivity software.

Bay Networks 58000 Ethernet Switch Module

System Up Time: 1 D-12H-22M-11S IP Address: 134.177.32.98(M)

MAC Address: 000081000201 Default Gateway: 134.177.32.1

Switch Software Version: 1.4.3 Subnet Mask: 255.255.255.0

Local VLAN Information

Port VLAN ID/Name Port VLAN ID/Name

1 [2/Default]

9 [2/Default]

2 [2/Default] 10 [2/Default]

3 [2/Default] 11 [2/Default]

4 [2/Default] 12 [2/Default]

5 [2/Default] 13 [2/Default]

6 [2/Default] 14 [2/Default]

7 [2/Default] 15 [2/Default]

8 [2/Default] 16 [2/Default]

9 [2/Default] MDA P1 [Trunk]

10 [2/Default] MDA P2 [Trunk]

11 [2/Default]

VLAN ID and name associated with port 1.

Use cursor keys to choose item. Press <RETURN> to confirm choice.

<CTRL><P>: Main Menu <CTRL><U>: Previous Menu <CTRL><L>: Refresh Screen

893-878-B Book Page 11 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands