Bay Networks 58000 Installation And Reference Manual Download Page 138

Page: 138 / 158

Configuring the Model 58000 Switch

6-32

893-878-B

To modify the boot parameters, follow these steps:

In the Main Menu, choose Configuration Parameters.

In the Configuration Parameters menu, choose Boot Parameters.

A Boot Parameters menu similar to that in

Figure 6-17

is displayed.

Figure 6-17. Boot Parameters menu

Choose Modify Boot Mode.

The system displays the current boot mode (either network or local) and
prompts you change the setting.The current boot mode is highlighted, and
the other boot mode option is displayed unhighlighted.

Bay Networks 58000 Ethernet Switch Module

System Up Time: 1 D-12H-22M-11S IP Address: 134.177.32.98(M)

MAC Address: 000081000201 Default Gateway: 134.177.32.1

Switch Software Version: 1.4.3 Subnet Mask: 255.255.255.0

Boot Parameters

Modify Boot Mode [Local]

Modify Image Load Mode [Local]

Modify Boot Router IP Address [123.123.11.1]

Modify TFTP Load Server IP Address [123.123.11.5]

Modify TFTP Retry Count [5]

Modify Image File Name [c:\comm\58k11e.img]

Change the boot mode to Local or Network.

Use cursor keys to choose item. Press <RETURN> to confirm choice.

<CTRL><P>: Main Menu <CTRL><U>: Previous Menu <CTRL><L>: Refresh Screen

893-878-B Book Page 32 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands