Bay Networks 58000 Installation And Reference Manual Download Page 48 | Manualshive

Page: 48 / 158

background image

Planning a Switched Network

2-10

893-878-B

Link Speeds

Use the 10Mb/s ports and the 100 Mb/s MDA ports to connect to 10 Mb/s and
100 Mb/s devices. Using the 100BASE-T MDA ports in full-duplex mode
achieves the greatest aggregate throughput of the Model 58000 switch, and
provides for greater distances between hubs.

Avoid using 10 Mb/s links between connected Model 58000 switches because
10BASE-T operates at 10 Mb/s half-duplex or full-duplex mode and does not
provide sufficient bandwidth for high-speed switched connections. When used,
10 Mb/s trunk link connections result in greatly diminished throughput along
the link.

Full-duplex Operation

Model 58000 switches support full-duplex mode for MDA ports operating at
100 Mb/s. For full-duplex mode, the CSMA/CD protocol is turned off and
frame transmissions occur in both directions along the link at the same time,
which increases the total bandwidth of the trunk link to 200 Mb/s and allows
link distances to be greater between switches. Full-duplex mode can be used on
links between the following devices:

•

Two Model 58000 switches that are connected using 100 Mb/s MDA ports

•

A Model 58000 switch and an end station (if the Ethernet end station
supports full-duplex operation)

The 16 10BASE-T ports on the front of the Model 58000 switch module also
support full-duplex mode when they are connected to external devices from the
front of the switch. The first 12 of these 10BASE-T ports can connect to the
backplane at half-duplex mode only.

NOTE:

Unless specifically configured for full-duplex operation, the

100BASE-T MDA ports and the 10BASE-T front panel connected ports default
to half-duplex mode. You can configure each port for either half- or full-duplex
operation using the service port screens. For instructions on how to configure
ports, refer to

, “Configuring the Model 58000 Switch.”

893-878-B Book Page 10 Monday, May 12, 1997 2:06 PM

«
...
46
47
48
49
50
...
»

Summary of Contents for 58000































































































































































Reviews:

No comments

Related manuals for 58000

SmartSwitch Router

Brand: Cabletron Systems Pages: 338

DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network...

Brand: D-Link Pages: 53

DG834GT - 108 Mbps Super G Wireless ADSL Router

Brand: NETGEAR Pages: 2

Brand: iBall Baton Pages: 9

RUGGEDMAX WIN7000

Brand: RuggedCom Pages: 42

Brand: NETGEAR Pages: 142

ADSL2+ Wireless MIMO Router

Brand: Ace Pages: 64

3C8567 - SuperStack II NETBuilder SI 567...

Brand: 3Com Pages: 6

Brand: Global Sun Pages: 39

Brand: Hunter Pages: 2

Ethernet MCA 10/100 Adapter

Brand: Olicom Pages: 88

Brand: Modecom Pages: 16

Brand: Hi-flying Pages: 59

Brand: Allied Telesis Pages: 128

Brand: Tenda Pages: 74

Brand: Waveshare Pages: 27

Brand: Waveshare Pages: 23

Brand: IC Realtime Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands