Bay Networks 58000 Installation And Reference Manual Download Page 9

Page: 9 / 158

893-878-B

Figures

Figure 1-1.

Model 58000 10/100 Ethernet Switch 1-2

Figure 1-2.

Location of Model 58000 switch in chassis 1-2

Figure 1-3.

Connecting to the Model 5000 backplane 1-5

Figure 1-4.

Model 58000-xxx MDAs 1-7

Figure 1-5.

MDA expansion module 1-7

Figure 1-6.

Fully equipped Model 58000 switch 1-8

Figure 1-7.

Hardware features of the switch (with MDA expansion module

installed) 1-9

Figure 1-8.

LED display on the Model 58000 switch 1-11

Figure 1-9.

MDA slot 1-12

Figure 1-10.

MDA expansion module slot 1-13

Figure 1-11.

Location of 10BASE-T ports on the switch 1-14

Figure 1-12.

Switch reset button 1-15

Figure 2-1.

Microsegmentation with the Model 58000 switch 2-4

Figure 2-2.

Virtual networking 2-5

Figure 2-3.

Multiple virtual LANs within a single Model 58000

switch 2-13

Figure 2-4.

Multiple virtual LANs across multiple Model 58000

switches 2-15

Figure 2-5.

Address allocation across trunk links where virtual LANs

are shared 2-17

Figure 2-6.

Sample configuration: auto port overrides forced

feeder ports 2-20

Figure 2-7.

Redundant connections from a single switch to an Ethernet

segment 2-21

Figure 2-8.

Redundant connections of two switches in a community to two

Ethernet segments 2-22

Figure 2-9.

Redundant connections of three switches in a community to three

Ethernet segments 2-23

Figure 2-10.

Redundant connections of different community switches to two

Ethernet segments 2-25

Figure 2-11.

Using forced feeder ports for switch community

connections 2-27

Figure 2-12.

Using forced feeder ports for redundant switch community

connections 2-28

Figure 2-13.

Multiple edge switches across switch communities 2-30

893-878-B Book Page ix Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands