Bay Networks 58000 Installation And Reference Manual Download Page 127

Page: 127 / 158

Using the System Configuration Menus

893-878-B

6-21

Select the new port duplex mode.

The system prompts you for confirmation. The modified ports use the new
duplex mode immediately.

Repeat steps 4 and 5 for additional ports.

Modifying Switch Port Front/Back Connection

To modify the switch port front/back connection, follow these steps:

Choose Configuration Parameters from the Main Menu.

The Configuration Parameters menu is displayed.

Choose Switch Parameters from the Configuration Parameters menu.

The Switch Parameters menu is displayed.

Choose Modify Switch Port Front/Back Connection from the Switch
Parameters menu.

A Switch Port Front/Back Connection menu similar to that shown in

Figure 6-10

is displayed.

NOTE:

The first 12 10BASE-T ports cannot be configured for full-duplex mode

when they are connected to the Model 500x chassis backplane.

893-878-B Book Page 21 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands