Bay Networks 58000 Installation And Reference Manual Download Page 130

Page: 130 / 158

Configuring the Model 58000 Switch

6-24

893-878-B

Choose the port you want to change.

The system displays the current type (Auto or Feeder) for that port and
prompts you to change the port type. The current port type is highlighted,
and the port type options are displayed unhighlighted.

Select the new port type, either auto or feeder.

The system prompts you for confirmation.

Repeat steps 4 and 5 for additional ports.

Modifying Switch Port Flow Control

To modify the switch port flow control, follow these steps:

Choose Configuration Parameters from the Main Menu.

The Configuration Parameters menu is displayed.

Choose Switch Parameters from the Configuration Parameters menu.

The Switch Parameters menu is displayed.

Choose Modify Switch Port Flow Control from the Switch Parameters
menu.

A Switch Port Flow Control menu similar to that shown in

Figure 6-12

displayed.

NOTE:

The new port type is not used until the Model 58000 is reset. See

Resetting the Model 58000 Switch

later in this chapter for information

about resetting the switch.

NOTE:

Flow control can be enabled only on 100 Mb/s MDA ports operating

in full-duplex mode.

893-878-B Book Page 24 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands