Bay Networks 58000 Installation And Reference Manual Download Page 128

Page: 128 / 158

Configuring the Model 58000 Switch

6-22

893-878-B

Figure 6-10. Switch Port Front/Back Connection menu

Choose the port you want to change.

The system displays the current connection for that port and prompts you
to change the connection. The current port connection is highlighted, and
the port connection options (either Front or Back) are displayed
unhighlighted.

Select the new port connection (either Front or Back).

The system prompts you for confirmation. The modified ports use the new
port connections immediately.

Repeat steps 4 and 5 for additional ports.

Bay Networks 58000 Ethernet Switch Module

System Up Time: 1 D-12H-22M-11S IP Address: 134.177.32.98(M)

MAC Address: 000081000201 Default Gateway: 134.177.32.1

Switch Software Version: 1.4.3 Subnet Mask: 255.255.255.0

Switch Port Front/Back Connection

Port Connection Port Connection

1 [Front]

7 [Front]

2 [Front] 8 [Front]

3 [Front] 9 [Front]

4 [Front] 10 [Front]

5 [Front] 11 [Front]

6 [Front] 12 [Front]

Change port 1 front/back connection.

Use cursor keys to choose item. Press <RETURN> to confirm choice.

<CTRL><P>: Main Menu <CTRL><U>: Previous Menu <CTRL><L>: Refresh Screen

893-878-B Book Page 22 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands