Bay Networks 58000 Installation And Reference Manual Download Page 146

Page: 146 / 158

Technical Specifications

A-2

893-878-B

Physical Specifications

Dimensions:

19in x 11in x 2.44in
48.26 cm x 27.94 cm x 6.20 cm

Weight:

5.1 lb
2.3 kg

Environmental Specifications

Operating temperature:

to 104

F (5

to 40

Operating humidity:

85% maximum relative
humidity, noncondensing

Operating altitude:

Up to 10,000 ft (3,050 m) maximum

Storage temperature:

–13

to 158

F (–25

to 70

Storage humidity:

95% maximum relative humidity

Electromagnetic Emissions

Meets requirements of:

FCC Part 15, Subpart B, Class A

EN55022 (CISPR 22), Class B (shielded cables required)

VCCI Class 1 ITE (shielded AC power cables required)

Electromagnetic Susceptibility

Electrostatic discharge (ESD): IEC 801-2, Level 3

Electrical fast transient/burst:

IEC 801-4, Level 2

Electrical surge:

IEC 801-5, Level 2/1

Safety Agency Approvals

UL 1950 with D-3 deviations

CSA 22.2 #950 with D-3 deviations

IEC 950 / EN 60 950 (TUV)

Designed to meet UL94-V1 flammability requirements

893-878-B Book Page 2 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands