Bay Networks 58000 Installation And Reference Manual Download Page 151

Page: 151 / 158

LED Functionality

893-878-B

B-3

Port
Status

Ports 1 to 12

Green

Port is connected to the Ethernet backplane
segment and is operating.

Amber

The segment is partitioned from the switch
through network management or other
means.

Off

Link status of the port is off.

Ports 13 to 16

Green

Link status of the port is on.

Amber

The port is partitioned.

Off

Link status is off.

FDx

Green

The port is operating in full-duplex mode.

Off

The port is operating in half-duplex mode.

Back
(Ports 1 to 12)

Green

The port is connected to the backplane.

Off

The port is connected through the front
panel.

Port
Activity

Green

Indicates the presence of data in the
transmit direction.

Off

Indicates no data present in the transmit
direction.

Green

Indicates the presence of data in the receive
direction.

Off

Indicates no data present in the receive
direction.

Col

Amber

Indicates collision or congestion.

Off

Indicates no collision or no congestion.

Table B-1. Model 58000 LEDs (continued)

Type

Label

Color

Meaning

893-878-B Book Page 3 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands