Bay Networks 58000 Installation And Reference Manual Download Page 107 | Manualshive

Page: 107 / 158

background image

893-878-B

6-1

Chapter 6

Configuring the Model 58000 Switch

This chapter covers the following topics:

•

System configuration parameters of the Model 58000 switch

•

An overview of system menus

•

Using the system configuration menus to configure system parameters

After installing the Model 58000 switch, you must configure a set of minimum
system parameters. See

Minimum System Parameters

later in this chapter for

more information.

You can perform advanced configuration for the Model 58000 switch using
Optivity network management software. For more information about how to
manage the Model 58000 switch with Optivity, refer to the user documentation
that shipped with your Optivity software.

System Configuration

This section describes the default configuration parameters of the Model 58000
switch and the minimum system parameters that must be configured after the
Model 58000 switch is installed.

Default Configuration

lists the default configuration parameters. You can modify these

parameters using the system configuration menus (see

Using the System

Configuration Menus

later in this chapter).

Table 6-1.

Configuration parameters

Parameter name

Default setting

Attachment port mode

Half-duplex

IP address (at initial installation)

0.0.0.0

Default gateway address

0.0.0.0

Subnet mask

255.255.255.0

Master switch priority

8000

Boot load mode

Local

893-878-B Book Page 1 Monday, May 12, 1997 2:06 PM

«
...
105
106
107
108
109
...
»

Summary of Contents for 58000































































































































































Reviews:

No comments

Related manuals for 58000

Brand: GE Pages: 4

Brand: Allnet Pages: 12

Brand: Telebyte Pages: 19

NetIron MLXe Series

Brand: Brocade Communications Systems Pages: 305

Brand: Patton electronics Pages: 13

Brand: Angel Cool Pages: 2

Brand: UfiSpace Pages: 34

Brand: NC-link Pages: 20

Sinus 154 data II

Brand: T-COM Pages: 12

Brand: Dahua Pages: 113

Brand: ActiveEye Pages: 35

Brand: Tripp Lite Pages: 3

Brand: Intellinet Pages: 12

Brand: Comtrend Corporation Pages: 208

Brand: Dynamix Pages: 87

32 bit 10/100 Fast Ethernet Card A02-S32-S

Brand: Atlantis Land Pages: 9

Prestige 642R Series

Brand: ZyXEL Communications Pages: 163

Brand: Pakedge Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands