Bay Networks 58000 Installation And Reference Manual Download Page 112 | Manualshive

Page: 112 / 158

background image

Configuring the Model 58000 Switch

6-6

893-878-B

•

[Ctrl]+U to return to previous menu.

•

[Ctrl]+L to refresh the screen and update displayed system information.

•

[Ctrl]+C to abort the current input.

•

[Ctrl]+T to break the connection to the System 5000

Menu Help Display

To display help information about any menu item, move the cursor to highlight
that menu item. A short description of the item is displayed just above the menu
command area of the screen.

Using the System Configuration Menus

You use the terminal that is connected to the System 5000 service port to access
the system configuration menus. From these menus, you can view system
information and configure the Model 58000 switch.

This section provides information and procedures on how to use the system
configuration menus to:

•

Display system startup messages.

•

Display the Main Menu.

•

Display system information.

•

Display local virtual LAN information.

•

Configure the minimum system parameters.

•

Modify master switch priority.

•

Modify port configurations.

•

Display and modify boot parameters.

•

Display and modify SNMP parameters.

•

Reset the Model 58000 switch.

•

Download an image file.

893-878-B Book Page 6 Monday, May 12, 1997 2:06 PM

«
...
110
111
112
113
114
...
»

Summary of Contents for 58000































































































































































Reviews:

No comments

Related manuals for 58000

Brand: Oracle Pages: 24

Marconi OMS 1200

Brand: Ericsson Pages: 136

Net2Air Ins-40085-US

Brand: Paxton Pages: 4

Brand: ZyXEL Communications Pages: 215

Brand: ZyXEL Communications Pages: 422

Brand: BHU NETWORKS Pages: 75

EtherLink 3C905C-TX

Brand: 3Com Pages: 96

Brand: Intercoax Pages: 2

ISDN SOHO Router

Brand: AOpen Pages: 89

Brand: Global Sun Pages: 39

Brand: Pakedge Device & Software Pages: 14

NVR41-4KS2 Series

Brand: Dahua Pages: 452

MP5S Plus Writer

Brand: SONIX Pages: 23

Brand: Xinje Pages: 76

Brand: Juniper Pages: 6

Brand: Axis Pages: 30

Brand: TCL Pages: 22

Brand: MSE Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands